Here’s how to recover data on an iPhone 13 Pro Max that is water damaged. This phone was in really bad shape, with rust everywhere.
So I walk through the full process on how I go about recovering the data.
First step is always removing all the unnecessary parts, like the screen, housing, battery and just completely removing the board out of the original housing.
Then we focus on just the motherboard.
Since this is a sandwich model, we use the X360 V2 board heater to split the sandwich, as we only need the top board to recover data from this model.
With just the top board, we inspect where all the corrosion is and clean it with Isopropyl alcohol and a toothbrush.
We then test the boarb with the DT880 (DC Power Supply) to check for shorts before & after prompt to boot. Surprisingly, this didn’t have any.
I tried to boot with a screen connected & found there was no image, as the display FPC connector was corroded and in really bad condition. So I replaced the connector & then found we...
If you have a Seek Thermal Cam, you're missing out if you don't have a VCC Seek Stand: https://www.vccboardrepairs.com/buy-seek-stand
Injured Gadgets just got these back in stock, so get them while you can!
It can take us a while to build these out sometimes, so they're sometimes out of stock for a while, but we're working towards always having inventory ready to build more as they sell out.
This stand makes using a thermal cam so easy. So much better than any other thermal solution on the market.
It allows you to get real close up (using my Macro Lens), and easily find where the short is coming from.
Plus it's hard free, so you can have your hands free to try to boot the device from DCPS, while having an image that is in focus & not moving around.
You can even record a video through the app, while you inject voltage into the short, so you can go back & see exactly which component was it that was heating up.
Save yourself lots of time by getting a Seek Cam, Stand & Macro Lens! ...
Anyone who is doing game console repairs, knows how many screws you need to remove to access the motherboard.
Especially the PS5, with the 5,000 screws or so.
If you don't already have an electric screwdriver, GET ONE ASAP.
🌟 Cordless Screwdriver with T9 Bit: https://amzn.to/3E5duCj
🌟Extended T9 Bit: https://amzn.to/3c4YJac
It's rechargeable through micro USB and allows you to easily swap the tips out. You can also fold it to be straight or L shape.
Let me know below if you are already using an electric screwdriver 👇👇
Crazy recovery job I wrapped up this week on an iPhone 14 Pro Max that was mailed in all the way from Nebraska.
Customer told me the phone had been run over multiple times, and honestly, after opening it up, I thought this was going to end up being a no-fix. The phone was absolutely destroyed. The housing was twisted, the board was severely bent, and the damage near the NAND had me expecting the worst.
First thing I did was remove the board and inspect everything under the microscope. The bend near the NAND and CPU area was pretty extreme, which is usually a very bad sign on these newer iPhones. In many cases, once the board bends this badly, the CPU or NAND can crack internally and the data is gone for good.
Because the board was bent so severely, I couldn’t safely use my normal board heater setup to separate the sandwich board. I had to carefully use hot air instead and take my time through the entire process. Definitely one of those jobs where one wrong move could destroy the last chance at ...
Have I got a please bro . Hahah
Thoughts on what is missing. Well it looks like a coil, but value guesses? It's an Omnex R160 wireless controller
This Pixel 6 came in for no power after another repair shop tried to repair the Display FPC connector (See pic1)
By the looks of it, they struggled badly trying to get this soldered on lol
So I found there were signs of overheating on the CPU and EERPOM chip, which was likely the fault. (See pic2)
I went through the full CPU Swap process, transplanting the CPU, RAM, UFS and EEPROM, only for the phone to bootloop & then give me the error in pic3
Unfortunately, it seems like something corrupted the UFS in the process, causing data not to be recoverable
This makes me sad, as an FPC replacement should be one of the easiest solder jobs to do, but this is what happens when inexperienced techs practice on customer's devices 😭
I totally get the urge to try it. You see videos... it looks easy.. you got some random hot air station & cheap iron combo from amazon
So why not?
Well this is why not.. you can totally kill the customer's device & data
If you want to learn how to solder, practice on ...
